Skip to content

Paddock stands

SPECSTAR VH569-BK

A front and rear paddock stand set with adjustable forks, titled at 400 kg while its own bullet states 200 kg per stand — both figures are reported here.

SPECSTAR front and rear paddock stand set

SPECSTAR VH569-BK

A front and rear paddock stand set with adjustable forks, titled at 400 kg while its own bullet states 200 kg per stand — both figures are reported here.

Capacity
The title states 400 kg for the set; the third bullet states 200 kg PER STAND. Both are published by the seller.
Front adjustment
Front wheel holder adjustable from 22.9 to 31 cm (maker’s bullet)
Rear adjustment
U-shaped support forks 28.5 to 36.6 cm, plus L-shaped supports (maker’s bullet)
Supplied as
A set — front and rear, usable together or separately (maker’s bullet)
Wheels
4 rollers (maker’s bullet)
Construction
Steel frame with a triangular geometry (maker’s bullet)
Amazon reference
B07ZSWJ4N3 (one reference across 6 Amazon marketplaces)
EAN
0885469880888
  • Both U and L supports supplied, which covers spool-less and spooled swingarms
  • Adjustment ranges published in centimetres for front and rear separately
  • The title capacity and the bullet capacity are not the same number

Best for: Getting both wheels off the ground with two stands rather than a jack.

≈ $60 / £56 / €73
Check price on Amazon

Specifications

Capacity
The title states 400 kg for the set; the third bullet states 200 kg PER STAND. Both are published by the seller.
Front adjustment
Front wheel holder adjustable from 22.9 to 31 cm (maker’s bullet)
Rear adjustment
U-shaped support forks 28.5 to 36.6 cm, plus L-shaped supports (maker’s bullet)
Supplied as
A set — front and rear, usable together or separately (maker’s bullet)
Wheels
4 rollers (maker’s bullet)
Construction
Steel frame with a triangular geometry (maker’s bullet)
Amazon reference
B07ZSWJ4N3 (one reference across 6 Amazon marketplaces)
EAN
0885469880888

Two capacities, one seller

The title says 400 kg.

The third bullet says each stand has a load capacity of 200 kg.

Both are published. A set of two stands each rated 200 kg does add to 400, and no single stand in this box carries 400 kg. Which number applies depends entirely on whether the machine’s weight is on one stand or shared across two — and it is on one, whenever you lift one end at a time.

That is why both are set down here rather than the larger one.

What the listing publishes otherwise

Front wheel holder adjustable 22.9 to 31 cm. Rear U-shaped forks 28.5 to 36.6 cm plus L-shaped supports. A steel frame with a triangular geometry. Four rollers. Front and rear usable together or separately.

Both adapter types is the useful part

An L-adapter engages the bobbins — the spools — screwed into a swingarm that has threaded mounts. A U-fork cradles the swingarm itself where it does not.

Machines differ, and a stand supplied with only one of the two either fits yours or does not. This set carries both, and the adjustment ranges in centimetres let you check against your own swingarm before ordering.

Availability

Between 73 € and 82 € across the German, French and Spanish Amazon stores, in the single reading behind this page.

Priced in local currency, which the euro range above deliberately leaves out, it also appears on the American and British Amazon stores.

More than 1.6× what the cheapest country asked was being charged on the Italian Amazon store. A gap of that width usually points to goods sent in from abroad rather than a seller on the ground, so that amount stays outside the range above.

What Keepa returned in the single reading behind this page. Availability and prices move without notice.

Prices quoted in this text were read on 18 September 2026. The live price is at the top of the page.

More paddock stands

  • VEVOR motorcycle scissor lift jack raised

    VEVOR Scissor lift jack 500 kg

    A motorcycle scissor lift jack rated at 500 kg, raising from 95 to 350 mm on a six-position safety pin, with a 365 × 222 mm non-slip platform that folds flat for storage.

    Capacity
    500 kg (from the title and bullet — the same figure in both)
    Height range
    95 to 350 mm (from the title)
    Safety pin
    Six positions, stated to hold the machine and reduce slipping (maker’s bullet)
    Platform
    365 × 222 mm, non-slip, extra wide (maker’s bullet)
    Folded height
    95 mm, for compact storage (maker’s bullet)
    Operation
    A removable metal handle turned to raise, no extra tools (maker’s bullet)
    Amazon reference
    B0C4KQGQ92 (one reference across 6 Amazon marketplaces)
    EAN
    0840349901596
    • The title figure and the bullet figure agree — which two stands in this family cannot say
    • A six-position mechanical safety pin, independent of the screw
    • A scissor jack lifts on the frame or engine — you must know where your machine takes a jack

    Best for: Lifting a machine clear of the floor for a chain, an oil change or winter storage.

    ≈ $54 / €45
    Check price on Amazon
  • Wiltec red rear paddock stand for motorcycles

    Wiltec 51267

    A rear paddock stand in powder-coated steel supporting tyres 200 to 340 mm wide, with a 370 × 325 mm footprint, four rollers and a stated 450 kg rating.

    Tyre width range
    200 to 340 mm (from the title and bullet)
    Footprint
    370 × 325 mm (from the title)
    Rating
    Up to 450 kg (from the title and bullet — the same figure in both)
    Material
    Powder-coated steel with a round tube structure (maker’s bullet)
    Rollers
    4 (maker’s bullet)
    Visibility
    Bright red paint, stated to increase visibility in the garage (maker’s bullet)
    Amazon reference
    B01IWKTF7S (one reference across 5 Amazon marketplaces)
    EAN
    4250390882083
    • Publishes a tyre WIDTH range, which is the fitment for a wheel-chock type stand
    • Title and bullet give the same rating
    • A tyre-width stand supports the wheel, so the rear wheel cannot be turned

    Best for: Holding a machine upright for cleaning, storage or transport.

    ≈ £49 / €45
    Check price on Amazon
  • XPOtool front wheel rocker stand for motorcycles

    XPOtool 63296

    A front wheel rocker stand in powder-coated steel for 17, 19 and 21 inch wheels with tyres 60 to 120 mm wide, with non-slip rubber feet and pre-drilled fixing holes.

    Wheel sizes
    17″, 19″ and 21″ (maker’s bullet)
    Tyre width
    60 to 120 mm (maker’s bullet)
    Mechanism
    Rocker — the wheel is ridden into it and it tips upright, with no second person (maker’s bullet)
    Material
    Powder-coated steel, stated for all weather conditions (maker’s bullet)
    Feet
    Non-slip rubber caps, stated to protect floor coverings (maker’s bullet)
    Fixing
    Pre-drilled holes to bolt it down (maker’s bullet)
    Amazon reference
    B0BS9RMZ1B (one reference across 5 Amazon marketplaces)
    EAN
    4251548134597
    • The only stand here that can be bolted to a trailer floor — pre-drilled holes are published
    • Wheel diameter AND tyre width both given
    • A 60–120 mm tyre width rules out wide front tyres

    Best for: Transporting a machine in a van or on a trailer, where it has to stand up on its own.

    ≈ £53 / €51
    Check price on Amazon

The rest of this rider’s shelf

  • Lamicall BP07 handlebar phone holder

    Lamicall BP07

    A handlebar phone holder for 4.7 to 6.8 inch devices with a quick-release clamp, one-handed operation and thick silicone at the four corners.

    Device size
    4.7 to 6.8 inch phones and GPS devices (maker’s bullet)
    Mounting
    Quick-release clamp, no tools — press a button to open (maker’s bullet)
    Operation
    Auto-retracting arms; press down with the phone to lock (maker’s bullet)
    Protection
    Thick silicone resin on the four corners and the contact surface (maker’s bullet)
    Vibration damping
    NOT published — two mounts in this family publish a damping system.
    Identical listing text
    Three of this listing’s bullets appear word for word in the Grefay listing in this same family, under a different brand and a different reference.
    Amazon reference
    B09MT4N4HW (one reference across 6 Amazon marketplaces)
    EAN
    8435611497888
    • Tool-free quick-release clamp, so it moves between machines
    • Published on all six marketplaces at a consistent price
    • No vibration damping published — the thing that damages a phone camera on a motorcycle

    Best for: A scooter or a low-vibration machine, or a bicycle, where damping is not the issue.

    ≈ $19 / £17 / €18
    Check price on Amazon
  • MOGGAM PH00 anti-vibration motorcycle phone mount

    MOGGAM PH00

    An anti-vibration phone mount with three fitting methods and a double silicone damping system, whose maker publishes which scooters it cannot be fitted to.

    Fitting methods
    Three — round bar 22 to 32 mm (4 rubber rings included), mirror thread M8 and M10, or mirror stem 12 to 14 mm with the 12 mm ring (maker’s bullet)
    Maker’s exclusion
    Scooters such as the TMAX and Forza have none of the three fitting points — the maker says so explicitly (maker’s bullet)
    Damping
    Double damping system in silicone, stated to absorb engine and road shock and protect the phone camera (maker’s bullet)
    Phone size
    5.4 to 7.2 inch, up to 15 mm thick with a case; the maker names its own thicker model for over 15 mm (maker’s bullet)
    Materials
    CNC aluminium ring and base, stainless steel telescopic arms, high-strength plastic platform with aluminium reinforcement (maker’s bullet)
    Operation
    One-handed in one second, 360° rotation (maker’s bullet)
    Amazon reference
    B0D2LVTZQC (one reference across 6 Amazon marketplaces)
    EAN
    0753389451030
    • Names the machines it will NOT fit, by model — the most useful bullet in this family
    • Three fitting methods with exact dimensions for each
    • The three fitting points have to be checked on your machine before ordering

    Best for: A machine with a free handlebar, a mirror thread or a mirror stem — checked before ordering.

    ≈ $28 / £35 / €28
    Check price on Amazon
  • SP Connect Moto Mount Pro handlebar mount in black

    SP CONNECT Moto Mount Pro

    A CNC aircraft-aluminium handlebar phone mount fitting four bar diameters from 22.2 to 31.7 mm, adjustable through 360 degrees in six-degree steps in portrait or landscape.

    Bar diameters
    22.2 / 25.4 / 28.6 / 31.7 mm — 0.875 / 1.0 / 1.125 / 1.25 inch (maker’s bullet)
    Material
    CNC-machined aircraft aluminium (maker’s bullet)
    Adjustment
    360°, in 6° steps; portrait or landscape (maker’s bullet)
    Supplied
    Moto Mount Pro, plastic spacing inserts, SPC+ Head and a Direct Adapter (maker’s bullet)
    System requirement
    This is a mount for a system — the phone needs the matching case or adapter, which is what the SPC+ Head and Direct Adapter are for.
    Damping
    The maker puts nothing in writing on this.
    Amazon reference
    B0721D5WNL (one reference across 6 Amazon marketplaces)
    EAN
    4028017531382
    • Four bar diameters published in both millimetres and inches, with spacing inserts supplied
    • Six-degree detents, so the angle set is the angle it keeps
    • A system mount — the phone needs the matching case or adapter, which is a further purchase for most phones

    Best for: A rider already in this maker’s case system, wanting a mount machined rather than moulded.

    ≈ $58 / £43 / €45
    Check price on Amazon

All paddock stands